10650 Fern Avenue • Unit F • Stanton, CA 90680 • Tel: 714-527-4874Fax: 714-527-4894Cell: 714-767-9818
Email: dabgcmm@aol.comwww.gcmmi.comwww.marseco.com • we accept Visa & Mastercard we accept Visa and Mastercard
Ask Us About Refurbished Deburrers in Stock



The conveyor rollers are constructed of a three piece design. Brass end plugs are machined and pressed into a steel tube. Neoprene rubber is then blown over the tubes forming a rigid yet resilient conveyor roll that is impervious to moisture and most chemicals, yet will not damage the most delicate of circuit boards.


Each brush is powered by an independent motor through a banded V-belt drive.

Abrasive wheel adjustment is accomplished by two special gear motors coupled to the bearing housing sides. This allows the abrasive wheel pressure to be independently varied to ensure a balance between top and bottom deburring. This precise control is monitored by two visual load indicating ammeters.

The brushes have a positive mechanical coupling, driven by a high torque gear motor, causing the brushes to oscillate 180° out of phase. This system eliminates the possibility of the phase balance being disturbed which would place undue stress on the machine.

The quick change brush system enables both upper and lower abrasive wheels to be changed in less than 15 minutes. The machine is designed to accommodate most abrasive wheels.

The bearing slides and housing are designed to transfer brush load to the system frame, thus eliminating undue stress on the internal frame plates. They are manufactured from anti corrosive aluminum bronze castings.

The back-up rollers are manufactured of stainless steel and flame coated for extended life. The upper roller is adjustable to compensate for the panel thickness and it's position is monitored by a dial indicator. The lower roller supports the bottom of the panel and is firmly mounted to provide zero reference.

The top and bottom brushes have brass spray nozzles (12 each for 24" wide systems, and 15 each for 30" wide systems) to cool both brushes and panel.

Rinse Section

The rinse section consists of four spray bars with strategically placed "High Pressure Jet Spray Nozzles" (15 top and 15 bottom for 24" wide systems, and 19 top and 19 bottom for 30" wide systems) which are designed to provide a positive overlapping rinse pattern. This assures complete rinsing and removal of loose particles from both panel surfaces and barrels of drilled holes.

Drying System

An efficient, filtered air system is the key to the drying principle. A high velocity pressure type self cleaning aluminum fan produces 1450 cubic feet of air per minute at 15 inches of static pressure. Ambient air is then fed through six uniquely designed airknives (three top and three bottom) that blast away any trace of moisture, including all through holes.

Other key features are:

  • The frame is constructed of welded angular steel and coated with high quality chemical and rust resistant paints.
  • The precision machined frame plates are fabricated of high impact stress relieved polyvinyl chloride and connected by heavy duty stainless steel bars to ensure positive warp resistant construction.
  • External covers are constructed of 1/4" PVC to withstand the most rugged abuse. They are custom fitted to obtain a streamlined finish.
  • Variable speed conveyor for precise process control and smooth positive roller action.
  • Optional variable speed brush oscillation 10-250 cpm.
  • Optional high pressure rinse system to 1,200 psi.
  • 24" and 30" wide models available.
  • Process parts 2"-24" in width, and 6" or longer in length.
  • Process parts 0.01" to 0.25" in thickness. 0.004" to 0.25" thickness with optional thin film guide system.
  • Control switches and indicators are conveniently located on the front of the machine.
  • Optional remote electrical control panel.
  • Low water usage which reduces operating costs.
  • Optional closed loop filtration system which removes particulate contaminates such as copper. Since this is a closed loop system, external water is not required which further reduces operating costs.
  • Optional thin film guide system.
  • Domestic and export power.

Deburrer Literature

Standard Deburrer
Deburrer Flyer
wet deburrer flyer
Wet Deburrer
Heavy Duty Deburrer
Heavy Duty
Deburrer Flyer
click to enlarge photos deburrer
Standard Deburrer. Several available with options, such as high pressure plumbing, stainless steel spray tubes/nozzles, high pressure pump 0-800 psi.
Heavy Duty Deburrer. Several available with various options such as, stainless steel side decks, etc.
Slide Supports and Slides for Heavy Duty and Standard Deburrers. deburrer
© Global Custom Machine Manufacturing, Inc.